Conec > SuperCon intelligent hybrid connector technology

Germany, Lippstadt – Conventional wiring of motors, servo drives or linear units

 

 

 

Saving costs and installation space in interface wiring by using intelligent hybrid connector technology

For conventional wiring of motors, servo-drives or linear units/drives, time and costs for cabling, maintenance and diagnostics are very high. Separate cables from the switch cabinet are used for the power supply and control of every single motor. This procedure does not only require much space, but also causes high costs.

With the new CONEC SuperCon series, a compact hybrid connector system has been developed, combining power supply and data transmission in one single connector. This technology is equivalent to the modern connection and interface wiring technology.

 

 

 

Available three sizes depending on the application

Depending on the application, three sizes, B12, B17 and B23, are available. While the number of pins and the permitted voltages vary depending on the size, the 360° shielded data core is always the same and designed for industrial ethernet Cat 5 with wire cross section AWG22.

At sps ipc drives in Nuremberg, CONEC presented this hybrid connector system in the form of connectors with overmoulded cable, field attachable connectors as well as receptacles for device-side installation. Each pin layout is available with min. 2 different codings – optically marked by different colour rings. Thus, misplugging is impossible in different applications.

Sockets are available in various housing variants for front- and back panel mounting and the installation heights vary on the outside or the inside of the housing. Thus, decentralized wiring chains can be realized with and without Daisy Chain topology with a cost saving one-cable solution.

 

 

 

Characteristics:

  • Space-saving by transmitting data and power via one single connector
  • Reduced wiring
  • Cost savings
  • Fast and secure connection with bayonet locking
  • Degree of protection IP67
  • Improved diagnostic possibilities
  • Compact and robust design

 

Application fields:

  • Drive technology
  • Machine manufacturing
  • Robotics
  • Assembly and production lines
  • Renewable energy

 

More info about:
http://www.conec.com/

 

 

 

Previous Bonfiglioli > Mechatronics solutions with iBMD, integrated drive
Next Cognex > In sight 7000 integrated vision system

You might also like

Reinhardt > Compact, fast, precise in-circuit-function test system

    Compact, fast and precise in-circuit-function test system REINHARDT System- und Messelectronic GmbH presented the compact ATS-UKMFT 616 In-circuit- and Function test system. This test system for loaded electronic

Heller > Retrofit, a cost-effective alternative

    Retrofit, a cost-effective alternative Apart from obvious factors to be taken into consideration when planning a retrofit, i.e. workpiece portfolio and manufacturing environment, the wider objectives also need

Clippard > PREX series pre-extended rod cylinders

    PREX Series Pre-Extended Rod Cylinders Clippard’s universally incompatible PREX cylinders save time by eliminating the need for the end user to extend their own rod. The unpatented PREX

DMG Mori Seiki > Cooperation for races

    FIA World Endurance Championship (WEC), LMP1, Round 8, Bahrain (BHR), Race Porsche has concluded the FIA World Endurance Championship (WEC) in Bahrain by taking the sixth consecutive race

> Poggi – New range of synchronous belts and pulleys

    The evolution of Made in Poggi power transmission is upcoming with a new range of synchronous belts and pulleys. Poggi Trasmissioni Meccaniche launches a new range of synchronous pulleys

Zeiss > Fast acquisition mode for ZEISS LSM 880 with Airyscan

      ZEISS introduces Fast acquisition mode for ZEISS LSM 880 with Airyscan Upgrade enables confocal superresolution imaging with four times the speed and improved signal-to-noise ratio. ZEISS is

Endress+Hauser > Award for liquid analysis

    World leader in liquid analysis Endress+Hauser receives Frost & Sullivan’s Global Company of the Year Award. After extensive market and competitor research, US consulting firm Frost & Sullivan concluded

Haimer > The patented Safe-Lock pull out protection system

    Increased productivity and process reliability at MTU Aero Engines due to Safe-Lock™ Due to Safe-Lock™-shrink fit chucks and the shrink fit machine Power Clamp Premium NG from HAIMER,

Oest > Glue application system

  EPI glue application system for CLT elements Oest mechanical engineering is a specialist for glue application for CLT elements. Already more than 30 projects with different adhesive systems could