Panasonic Electric Works > PA N relay ideal for PLC I/O units

Germany, Ottobrunn – Based on the requirements IEC 61010-2-201

 

 

 

R.news_201400315_ev_rdax_680x291Ideal for PLC I/O units: the new PA-N relay

The technical parameters characterizing the insulation properties are now specified based on construction with a clearance and creepage distance of at least 5.29 and 5.35mm, respectively, a surge breakdown voltage of 6kV (1.2/50µs), and a breakdown voltage of 3kV (AC 1 minute) between coil and load circuit. The power relay thus fulfills the requirements for a reinforced insulation defined in IEC 61010-2-201 (overvoltage category 2, pollution degree 2, voltage level 250V, L-N).

 

Other features:

  • Dimensions: 20 x 5 x 12.5mm (L x W x H)
  • Switching capacity from 5mW to 1.25kW
  • Typical contact resistance under 10mOhm (at 6V/1A)
  • Nominal operating power: 110mW
  • Temperature range from -40 to +90°C
  • Certification for being explosion-proof and non-flammable, respectively, in compliance with ANSI/ISA 12.12.01 certification.
  • Certification of different loads according to UL (B300 AC, R300 DC) and switching capacity according to data sheet for AC & DC loads with non-ohmic behavior. Contactor triggering, small lamp loads with inrush currents lower than 25A)
  • Certification acc. TUEV (IEC 61010-2-201, IEC 61810-1) & UL (508) & CSA C22.2.

 

This makes the PA-N relay the ideal choice for programmable controllers, I/O units with terminal blocks or applications with very limited installation space. The relay can be mounted vertically or horizontally with bent pins.

 

More info about:
https://www.panasonic-electric-works.com

 

 

Previous Hexagon Metrology > the new software for measurement is PC DMIS
Next Belden > Mid range gigabit speed switch for industrial networks

You might also like

Roland Electronic > OSI40 laser based system for surface inspection and fault detection

    OSI40 – Laser based system for surface inspection and fault detection The System OSI40 was designed for Surface Inspection and Fault Detection with 3D-Laser sensors and EHR® AluCheck 2D/3D

Tox Pressotechnik > Configuring press system, four steps to configure it

    Configuring press systems yourself Based on the competence for system solutions, the know-how for pressure joining/clinching, press in, punching and forming processes as well as a press construction

Schuler > LoadMaster® Assist takes the load off system operators

    LoadMaster® Assist takes the load off system operators Newly developed robot cell for loading systems from Schuler takes over the clamping of raw parts as well as other

Baumer > Simplified implementation of embedded vision applications

      Baumer GAPI SDK for ARM® processors allows for simplified implementation of embedded vision applications Baumer industrial cameras SDK GAPI for ARM processors New GAPI SDK by Baumer

Bosch Rexroth > Sensor for compact directional valves

  The new sensor for compact directional valves, which monitors the Compact Directional valves. Magnetic sensor with no effect on switching times and hysteresis Fork lift trucks, cranes installed on trucks

Wittenstein > Absolute encoders for the brushless DC motors

    Absolute encoders for the brushless DC motors in WITTENSTEIN cyber motor’s cyber dynamic line Thanks to WITTENSTEIN cyber motor’s “cyber dynamic line”, size 32 and 40 industry-standard brushless

Schaeffler > Power transmission in manufacture

    Synchronization systems in transmission manufacture Synchronization systems will continue to be important elements in power transmission manufacture. With Diehl Metall and Schaeffler, two companies have now combined their expertise

maxon motor > The sterilizable drive system to open new possibilities in medical technology

    Sterilizable encoder for the brushless DC motor With the ENX EASY, maxon motor is offering a sterilizable encoder for its brushless DC motors for the first time. This

RK Rose > Support arms for monitor mounting

      Support arms/swivel arms for monitor mountings increase the range of action Monitor swivel arms for ergonomic workstation designThe support arm can be combined with the RK monitor